IBHC0358 page 1 of 6 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0901a part no. chip lens color material emitted color IBHC0358 ingan blue water clear
absolute maximum ratings at t a = 25 ?c parameter symbol rating units forward current i f 25 ma reverse voltage v r 5 v operating temperature t opr -40 to +85 ?c storage temperature t stg -40 to +90 ?c electrostatic discharge esd 150 v power dissipation p d 110 mw peak forward current (duty 1/10 @ 1khz) i fp 100 ma soldering temperature t sol reflow soldering: 260? for 10 sec. hand soldering: 350? for 3 sec. electronic optical characteristics (t a = 25 ?c) parameter symbol min. typ. max. units condition luminous intensity i v 45 90 mcd i f = 5 ma viewing angle 2 1/2 60 deg peak wavelength p 468 nm dominant wavelength d 470 475 nm spectrum radiation bandwidth ? 25 nm forward voltage v f 2.60 3.00 v reverse current i r 50 a v r = 5 v notes: 1. tolerance of luminous intensity: ?1% 2. tolerance of dominant wavelength: ? nm 3. tolerance of forward voltage: ?.05 v IBHC0358 page 2 of 6 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0901a
bin range of dominant wavelength bin min max unit condition y 470 475 nm i f = 5 ma bin range of luminous intensity bin min max unit condition p1 45 57 mcd i f = 5 ma p2 57 72 q1 72 90 bin range of forward voltage group min max unit condition t 2.60 2.70 v i f = 5 ma 2.70 2.80 2.80 2.90 2.90 3.00 notes: 1. tolerance of luminous intensity: ?1% 2. tolerance of dominant wavelength: ? nm 3. tolerance of forward voltage: ?.05 v IBHC0358 page 3 of 6 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0901a
typical electro-optical characteristics curves: IBHC0358 page 4 of 6 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0901a
reel dimensions: carrier tape dimensions: IBHC0358 page 5 of 6 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0901a
precautions for use 1. over-current prevention: a series resistor must be used for protection against over-current. since slight voltage shifts can cause large current changes and possibly damage the led. 2. storage: 2.1. store the leds in the sealed moisture proof bag until ready to use. 2.2. the storage conditions should be below 30? and 90% rh or less. 2.3. unused portions of leds may be stored in moisture proof packages for up to 1 year if kept under 30? and at no more than 60% rh. 2.4. if there is evidence of moisture absorption or if the leds have been stored for a long time, bake the leds at 60? ?5? for 24 hours prior to using. 3. reflow soldering conditions: 3.1. pb-free solder temperature profile (see figure): 3.2. reflow solder no more than two times and must include time interval for the board to cool. 3.3. when soldering, do not put stress on the leds during heating. 3.4. after soldering, do not warp the circuit board. 4. hand soldering: use a low wattage soldering iron (below 25 watts) with a tip temperature no more than 350? for 3 sec or less on one terminal. wait at least two seconds before soldering the next terminal to avoid overheating the led and damaging it. 5. avoid reworking a soldered led. it is best to simply replace it with a new part. IBHC0358 page 6 of 6 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0901a
|
